Custom Precision Mould Design,Precision Mould Design Manufacturers

What is the most important during designing a mould ? May 27, 2019
The most important point is structure , If the structure can be simplified as much as possible, but the quality of the mold must be guaranteed, the company will earn the maximum profit from it . When we received a product , the first question is find out the biggest parting surface , Roughly determine the cavity and the core , then , To Analyze the construction of cavity and core , insert , ...
- Mould design
- mould processing
- plastic injection molding
Correct gate type and location for plastic mold Jun 10, 2019
When we design a mould , to chosing the gate type and location is very important. It will caused processing problem , even the quanlity of plastic products. Mould design engineer shouldn't only calculate for plastic products , but also should especially pay attention to the design for gate. They must chose the correct gate type , the numbers of gate and location . The gate type a...
Short Shot Injection Molding Jun 14, 2019
Insufficient injection is also called short shot. Short shot is the phenomenon of partly incomplete at the end of the material flow, or a part of the cavity filled with dissatisfaction, especially the thin wall area or the end area of the the runner when injection molding. When the melt is cooled down without filling the mold cavity, or the melt does not fill completely after running into the cavi...
- short shot injection molding
- mold cavity
- mould temperature
What to consider when designing the plastic mold? Jul 19, 2019
There are some points that should be noticed when plastic mould design: 1.The draft angle should be designed to be more than one degree. 2. It is suitable to select the direction of the projection surface of the plastic part as the direction of forming pressure, which is convenient for the material to fill the cavity, but it is not suitable for the part with high dimensional accuracy and the axis ...
- plastic mould design
- pre-hardened plastic mould
- high polishing mold
The short shot checkpoints Jun 28, 2019
The short shot checkpoints As mentioned that, when the melt is cooled down without filling the mold cavity, or the melt does not fill completely after running into the cavity, it is called the short shot injection molding. We analyse the reasons of short shot. So today let’s discuss how to improve the insufficient injection. Here lists short shot checkpoints: 1) Improper control of process conditi...
- mould temperature
- mold cavity
- short shot injection molding
There are undercuts around products'4 corner,should we make lifter or slider? Jul 08, 2019
As we know, During mold designing, If the product has inner undercut, we usually make lifter, If has outside undercut, we will make slider, But If it has undercut around the 4 corner, and couldn't be forced demoulding, what should we do? As below picture, should we make lifter or slider? 1. Design Analysis If so, first we will think about to make lifter, but after analyze, If make lifter the...
- Mold designing
- demould
- injection mould
What is 'Catch hook and thin-wall' of plastic mold products? Sep 18, 2019
What is 'Catch hook and thin-wall' of plastic mold products? 1. The Catch hook The catch surface and the amount of catch hook are the important basis for the test data during assembe. Once made any tiny mistake about these numbers, It would become a huge mistake of the product. Therefore, during mould design, We needs to pay special attentin to the catch hook assembly and testing. 2. The thin-wall...
- Mould design
- Plastic mould
- plastic injection mold
Actual Case Analysis of Poor Shrinkage (1) Jul 26, 2019
Today we are going to discuss one case for the sink mark, we will show what we would do when we face the sink mark problem. 1. Basic information: PE, Holder (car parts) shrinks poorly and snakes are bad. 2. Description: The plan to increase the injection pressure has not been solved. In order to make the resin pressure fully function, the gate thickness is increased and the sink mark is improved. ...
- injection mould design
- injection molding parts
- plastic auto molding

1 ... 3 4 5 6 7 ... 13

A total of 13 pages

Categories

Blog

New Blog

Tags

Search