Custom Design For Injection Molding,design For Injection Molding Manufacturers

What is Over-Mold? Mar 21, 2019
When We say "Over-Mold" means the secondary injection molding of the product. The main product consists of two parts, one refers to the plastic inside, and the other refers to the soft part outside. At the time of mold manufacturing, a plastic mold, that is, a main hard mold, is first manufactured. After he cools naturally, he puts it in another pair of molds and re-inserts the m...
- plastic over-mold
- TPU part mold
- secondary injection mold
Undercut in Plastic Mold Mar 29, 2019
In some plastic products, there are undercuts. If it is a small undercut, and the requirements of shape and size accuracy are low, or the plastic material has sufficient plastic deformation and toughness, the parts can be ejected/ demoulded by force. According to the different structures and requirements of plastic parts, the slider and lifter mechanisms is adopted to solve the problems in m...
- Plastic mold
- plastic parts
- mold design
Importance of adjusting the plastic injection mold temperature Mar 29, 2019
In the injection mold industry, the design of the structure for plastic products is very important, but if the temperature of the injection mold is not reasonable, no quality products will be produced, especially in the production of POM (polyoxymethylene), PA (nylon). When do PBT and PET (polyester) material, the mold temperature has a great influence on the plastic part. After reasonable t...
- injection molded product
- high precision injection
- plastic mold cooling
The Standardization Degree And Application Level Of Mould Equipment Are Important Signs To Measure The Level Of Mould Industry. Mar 29, 2019
The standardization degree and application level of mould equipment are important signs to measure the level of mould industry. The standardization degree and application level of mould equipment are important signs to measure the level of mould industry. Mold equipment is a special tool for forming tools, although it is highly personalized, but also an industrial product. Therefore, the standardi...
The Precision Of The Mold Will Be Higher And Higher Apr 04, 2019
With the continuous development of the economy, people's living standards are increasing, and the demand for spiritual and material culture is becoming higher and higher. This demand has also led to the continuous development and innovation of the home industry. The industry has a growing demand for home hardware, and the household hardware industry has shown a different change. The mold industry ...
The checking points for mold flash part Apr 12, 2019
It's very common to see some flashes on the part during mold testing. Today we are going to discuss some check points when we get flashed parts. 1. Mold fitting 2. Parting Line (PL) problem (1) Check if the surface of the core is higher than the surface of the AB plate (about 0.5MM) (2) Check the flatness of the surface to see if it is deformed because the mold plate is too thin. (3) Is there any ...
- plastic mold fitting
- mold plate
- molding machine tonnage
Mold Texture Discussion Apr 12, 2019
Texture is a common process for mold surface treatment, which directly affects the appearance and surface strength of the product surface. Mold texture, also known as mold etching, mold graning, is widely used due to its low process cost, rich effect and fast speed. It's use chemical liquid (such as sulfuric acid, nitric acid, etc.) to chemically react with the mold steel, and the reaction p...
- mold surface treatment
- injection molded parts
- mold graining
The advantages for Hot Runner Mold Apr 22, 2019
The hot runner mold refers to a mold that uses a heating device to keep the melt in the flow passage from solidifying at all times. Because it is shorter than the traditional mold shot cycle and saves raw materials, hot runner molds are widely used in various industrialized countries and regions in the world today. Shorten cycle The molding cycle is shortened. Because there is no restriction on th...
- hot runner mold
- plastic molding
- cold runner mold

1 ... 4 5 6 7 8 ... 24

A total of 24 pages

Categories

Blog

New Blog

Tags

Search