Custom Plastic Molding Surface,Plastic Molding Surface Manufacturers

Solution for defects of transparent plastic injection parts Feb 15, 2019
(1) eliminate the interference of gas and other impurities, and fully dry the plastic. (2) reduce the feed temperature, adjust the feed barrel temperature in stages, and appropriately increase the mold temperature. (3) increase the injection pressure and reduce the injection speed. (4) increase or decrease the preplasticized back pressure, reduce the screw speed. (5) improve the exhaust condition ...
- plastic injection mold
- plastic mould
- injection molding
Causes of color defects in injection parts Feb 15, 2019
(1) poor mold finish, mold surface rust, mold exhaust is bad. (2) if the casting system of the mold has defects, the cold feed well should be increased, and the flow passage, polishing mainstream passage, diversion passage and gate should be increased. (3) the material temperature and mold temperature are low, if necessary, local heating method of gate can be used. (4) low processing pressure, slo...
- plastic injection molding
- custom plastic part
- injection mould.
Requirements of Thin-wall Injection Molding to Mold Feb 15, 2019
Speed is one of the key factors for the success of thin-wall injection molding. Rapid filling and high pressure can inject molten thermoplastic material into the mold cavity at high speed, to prevent the gate from freezing. If a standard part fills in two seconds, the mold thickness will be reduced by 25%, and the filling time may be reduced by 50% (saving 1 second in time). When thickness decreas...
- injection molding
- hot runner mold
- standard mold
What is the effect of mold flow analysis on the mold? Feb 22, 2019
1. You can know if the part is full. The analysis can also provide other useful information such as the required injection pressure and clamping pressure. 2. You can know if the part has a filling problem. Many filling problems, such as short shots, bubbles and unbalanced filling, can be determined by careful analysis of the filling curve. Mold flow analysis allows you to change the position of th...
What is double injection mold? Mar 02, 2019
Double Injection Mold, also known as two material molding, 2 shot molding or 2K molding, is a manufacturing process used to produce complicated molded parts from two different materials. Two kinds of plastic materials are injected on the same injection machine, and they are formed twice, but the product is only molded out at once. This injection molding is usually completed by one mold and require...
- injection molding
- 2 shot molding
- double injection mold
Venting of plastic injection molds Mar 02, 2019
It is well known that the exhaust of injection mold is a problem that cannot be ignored in the mold design.Mold inner product set in the normal production of gas mainly has the following sources: 1. The feed system and the entities of the air in the cavity. 2. The plastic contains moisture evaporation and water vapor generated at high temperature. 3. The gas produced by plastic decomposition. 4. S...
- plastic injection molding
- custom plastic part
- mold manufacture
Procedures of Plastic Thermoforming Mar 15, 2019
The basic process of hot thermoforming is: clamping, heating, molding, cooling, demoulding. Among them, molding is the most important and complex. Plastic thermoforming is mostly carried out on the moulding machine, which varies greatly with the different methods of thermoforming. Not all kinds of moulding machines are required to complete the above five processes, and it can be chosen accor...
- Plastic Thermoforming
- plastic parts
- molded parts
Surface Lettering Method for Plastic Mold Mar 21, 2019
We often see patterns and numbers on plastic parts, and these numbers varies for each part. How to engrave these numbers and patterns on these molds? there are mainly three common methods. 1) The first one is directly engraved on the mold by an engraving machine. This is usually used when the font or pattern is large. Usually this type of font usually has a knife mark on the surface and needs to b...
- Mold engraving
- Mold surface lettering
- laser engraving

1 ... 3 4 5 6 7 ... 25

A total of 25 pages

Categories

Blog

New Blog

Tags

Search