Custom Mould Maker In Shenzhen China,mould Maker In Shenzhen China Manufacturers

What is Ejector Marks? Apr 12, 2019
Ejector mark is the phenomenon of stress whitening and stress elevation where appears on the opposite side of the nozzle facing the product, or where the ejector rod is located on the ejecting side of the tool. Why will it cause the ejector marks? The physical reason is when the demoulding force is too high or the surface of the ejector rod is relatively small, the surface pressure will be very hi...
- ejector marks
- tool
- demoulding
The checking points for mold flash part Apr 12, 2019
It's very common to see some flashes on the part during mold testing. Today we are going to discuss some check points when we get flashed parts. 1. Mold fitting 2. Parting Line (PL) problem (1) Check if the surface of the core is higher than the surface of the AB plate (about 0.5MM) (2) Check the flatness of the surface to see if it is deformed because the mold plate is too thin. (3) Is there any ...
- plastic mold fitting
- mold plate
- molding machine tonnage
Mold Texture Discussion Apr 12, 2019
Texture is a common process for mold surface treatment, which directly affects the appearance and surface strength of the product surface. Mold texture, also known as mold etching, mold graning, is widely used due to its low process cost, rich effect and fast speed. It's use chemical liquid (such as sulfuric acid, nitric acid, etc.) to chemically react with the mold steel, and the reaction p...
- mold surface treatment
- injection molded parts
- mold graining
Plastic Mold Manufacturing is Importance as Well Product Design Apr 12, 2019
When trying to develop products or new products, don't just focus on product design, neglect plastic mold manufacturing. Some users tend to focus only on product development and development, ignoring communication with plastic mold manufacturers. After initial determination of the product design plan, there are two advantages of contacting the mold manufacturer ahead of time. 1. You can ensu...
- plastic mold manufacturing
- high quality plastic mold
- mold maker
The advantages for Hot Runner Mold Apr 22, 2019
The hot runner mold refers to a mold that uses a heating device to keep the melt in the flow passage from solidifying at all times. Because it is shorter than the traditional mold shot cycle and saves raw materials, hot runner molds are widely used in various industrialized countries and regions in the world today. Shorten cycle The molding cycle is shortened. Because there is no restriction on th...
- hot runner mold
- plastic molding
- cold runner mold
Injection Mold Cooling Water Leakage Failure and Troubleshooting Apr 22, 2019
Injection mold cooling water leakage is a frequent occurrence, for many reasons, mainly in the following aspects: 1. The most occurs at the joint of the mold cooling water pipe. If water leakage is found, the sealing tape should be wound around the thread of the pipe joint and then tightened. 2. Due to long-term molding conditions, the waterproof ring inside the mold will be damaged, and the O-sha...
3D Printing Molds Accelerate Application Precision Parts Manufacturing Enters a New Era Apr 22, 2019
At present, with the continuous maturity of technology, 3D printing has been applied to industries such as automobile and aircraft precision parts manufacturing. With the promotion of 3D printing technology, the effect of the entire precision parts manufacturing has been further improved. As we all know, mold manufacturing and manufacturing are closely related to all areas. In order to meet the ne...
Preparations Before Mold Trial Apr 26, 2019
Mold trial is an essential part of the new mold before injection production, The quality of the test results will directly affect whether the subsequent production of the factory is smooth. What precautions should be paid attention to when test the mold? 1. Familar with the relevant information of the mold It is better to get the mold drawing, analyze it in detail, and get the mold technician to p...
- mold accessories
- plastic mold trial
- injection molding machine

1 ... 6 7 8 9 10 ... 29

A total of 29 pages

Categories

Blog

New Blog

Tags

Search