Custom Injection Mould Design,Injection Mould Design Manufacturers

How to improve the quality of molds? Nov 30, 2018
There are 3 basic ways to improve the quality of molds. Firstly, mold design is the most important step to improve the mold quality. Many factors need to be taken into account, including the selection of steel materials, the usability and safety of mold structure, the machinability of parts and the convenience of mold maintenance. All above factors should be considered at the very beginning ...
- Mold design
- Hot runner mold
- Mold lifetime
plastic injection molding, plastic surface, plastic mold. Nov 30, 2018
The parting surface is the joint surface of the mold for taking out the product in the process of injection molding. An important factor that decides the structural form of the mold, it is related to the overall structure of the mold, the design of the pouring system, the demoulding of the plastic parts and the manufacturing process of the mold. Selection principle of parting surface: A. The maxim...
- plastic injection molding
- plastic mold
- plastic surface
What Causes Insufficient Steel Hardness? Nov 30, 2018
The hardness of mold heat treatment is a very important mechanical property index,it is a very serious defect when the hardness is not qualified . Insufficient or uneven hardness of the mold after heat treatment will reduce the wear resistance and fatigue strength of the mold and other properties,even resulting in early failure of the mold, seriously shorten the mold life. The Reasons Causing: 1) ...
- Hardened mould
- mould forging process
- large mold
Reverse Engineering in Mould Making Dec 11, 2018
Geometric modeling technology has been widely used in the development of plastic products. However, due to various reasons, the technical data that mould makers get from clients is not the CAD model, but the physical samples consisting of complex free curves and surfaces. If using the traditional method to design and manufacture product, the cycle time is long and the cost is high. It is unable to...
- Reverse Engineering
- Rapid prototyping
- Mould making
Basic Design Principles for Gas Assisted Injection Mold(1) Dec 14, 2018
Today we are going to discuss basic design principles for gas assisted injection mold 1. When designing, first consider which wall thickness needs to be hollowed out, which surface shrinkage needs to be eliminated, and then consider how to connect these parts into the airway. 2. Large structural parts: full thinning, partial thickening for the airway. 3. The airway should be evenly distributed to ...
- gas assisted injection mold
- gas injection
- plastic gas assisted mold
Basic Design Principles for Gas Assisted Injection Mold(2) Dec 20, 2018
Today we will go on to discuss the basic design principles for gas assisted injection mold 11. Accurate cavity size is very important. 12. The symmetrical cooling of various areas of the product is very important. 13. When using gate inlets, the balance of flow is important for uniform of gas penetration. 14. The exact amount of injection is very important, and the Injection volume error should no...
10 factors that influence the quality of injection mold Dec 20, 2018
Mold manufacturing is a complex process, from the design, processing, assembly, debugging and other steps, to the final actual use. In the whole life cycle, the factors affecting the quality of mold mainly have the following 10 aspects. 1. Mold steel is the decisive factor of mold quality thus the choice of reasonable steel is the top priority. 2. Reasonable mold structure can effectively extend t...
- plastic injection molding
- plastic part
- mold quality
Design and Manufacturing Elements of Blow Molds Dec 26, 2018
The design and manufacture of blow molds with fast cycle times and long life is required for the development of the blow molding industry. The factors that determine the efficiency of the mold are: 1. Material 2. Cooling 3. Venting Material The material from which the mold is made must have high thermal conductivity and sufficient cutting edge strength. Curr...
- design of blow mold
- plastic blow mold
- blow molding manufacture

1 2 3 4 ... 25

A total of 25 pages

Categories

Blog

New Blog

Tags

Search