Custom High Cavitation Injection Molds,high Cavitation Injection Molds Manufacturers

What is snake mark and how to solve it? Jul 12, 2019
Snake mark is an indication when injection molding. So what will cause the snake mark? When injecting a plastic part, the Gate is smaller, while the space of the mold cavity is relatively larger. At this time, the temperature of resin is cooling down before it fullly injects into the whole mould cavity frame. Therefore, it will have a flowing marks remaining on the part surface like a snake crawli...
- injection molding
- snake mark
- mold cavity
What is 'Catch hook and thin-wall' of plastic mold products? Sep 18, 2019
What is 'Catch hook and thin-wall' of plastic mold products? 1. The Catch hook The catch surface and the amount of catch hook are the important basis for the test data during assembe. Once made any tiny mistake about these numbers, It would become a huge mistake of the product. Therefore, during mould design, We needs to pay special attentin to the catch hook assembly and testing. 2. The thin-wall...
- Mould design
- Plastic mould
- plastic injection mold
Actual Case Analysis of Poor Shrinkage (1) Jul 26, 2019
Today we are going to discuss one case for the sink mark, we will show what we would do when we face the sink mark problem. 1. Basic information: PE, Holder (car parts) shrinks poorly and snakes are bad. 2. Description: The plan to increase the injection pressure has not been solved. In order to make the resin pressure fully function, the gate thickness is increased and the sink mark is improved. ...
- injection mould design
- injection molding parts
- plastic auto molding
Analysis of the reasons for slow production during injection molding Jul 26, 2019
The reasons for the slow production during injection molding and the solutions are as follows: (1) The plastic temperature and mold temperature are high, resulting in long cooling time. (2) The glue is long. The back pressure should be reduced, the recycled material should be used less to prevent overhead, and the feed section should be cooled sufficiently. (3) The movement of the machine is slow....
- mold Filling
- injection molding machine
- plastic mold Filling
Bank Marks in Mirror-polishing Mould Jul 26, 2019
It is not easy to finish a set of high precision mould of mirror polishing. During polishing, the issues of smoothness of the mould may occur. There are some phenomenas such as graining, orange peel, ripples and bank marks on the mould surface. Today, let's talk about bank marks. Usually, there are two main reasons causing bank marks when mirror polishing the moulds. 1. It is due to the uneven met...
- mirror polishing
- high precision mould
- mould steel
Annealing of plastic products Aug 09, 2019
The annealing treatment of plastic products refers to the plasticization unevenness of the plastic in the cylinder or the uneven cooling rate of the product in the cavity, which causes the internal stress of the product to cause deformation, cracking and aging of the product in the future. The annealing treatment is carried out indoors, using a hot liquid medium such as hot water, hot minera...
- mold Filling
- plastic mold Filling
- injection molding machine
What is venting defective of product? Aug 19, 2019
When the injection machine starts to molding，the hot melt plastic flows in the mold cavity and squeezes the air in the mold cavity. If the air cannot be discharged effectively, it will cause venting, and the result will be that the product is short-shot or affects the quality. Under this situation, We need to check the injection speed, the mold temperature, Or add venting groove.
- injection mold
- Plastic mould
- molding
Analysis of the causes of unstable size of injection molded products -1 Aug 23, 2019
The dimensional change of plastic parts is essentially caused by the different shrinkage of plastics. Any change in material temperature, mold, pressure, and production cycle will lead to changes in the size of the part, especially PP, PE, nylon, etc. with higher crystallinity. The main reasons are as follows: 1. Machine side: (1) If the plasticizing capacity is insufficient, a machine with a larg...
- mold Filling
- injection molding machine
- plastic mold Filling

1 ... 7 8 9 10 11 ... 22

A total of 22 pages

Categories

Blog

New Blog

Tags

Search