Abs Case Mould

Injection molding and blow molding Sep 18, 2019
Plastic molding is a process in which a synthetic resin is used to make a final plastic product. Processing methods include: compression molding (molding), extrusion (extrusion), injection molding (injection molding), and blow molding (hollow molding). Let's distinguish between the molding process of injection molding and blow molding. (1) Injection molding: Injection molding is a method in which ...
- Blow Molding
- bottles molding
- Plastic Bucket Mould
What is venting defective of product? Aug 19, 2019
When the injection machine starts to molding，the hot melt plastic flows in the mold cavity and squeezes the air in the mold cavity. If the air cannot be discharged effectively, it will cause venting, and the result will be that the product is short-shot or affects the quality. Under this situation, We need to check the injection speed, the mold temperature, Or add venting groove.
- injection mold
- Plastic mould
- molding
Actual Case Analysis of Poor Shrinkage (3) Aug 23, 2019
Today we are continuing to discuss the 3rd case for the sink mark, we will show what we would do when we face the sink mark problem. 1. Basic information: PC combination transparent block, poor shrinkage 2. Description: there is not enough holding pressure time, but it is easy to cause flash by increasing the injection pressure. 3. Improvement: Increase the holding pressure time (with a pressure o...
- transparent part mold
- PC resin mould
- plastic molded part
What is the different between plastic mould and plastic injection mould? Sep 09, 2019
Plastic mould include injection mould, plastic injection mould is one of plastic mould. Plastic mould is a joint name of compression mould, extrusion mould, injection mould, blow mould and foaming mould. Plastic mould is a tool to manufacture plastic products, it could make plastic products to be more complete and the size more accurate.
- Plastic injection mold
- foaming mould
- extrusion mould
Plastic injection product defects discussion Sep 18, 2019
Today we are going to discuss common defects for plastic injection products. 1. Short shot The plastic part is insufficiently filled (or the injection pressure is not enough, the mold nozzle is too small). 2. Ejector Mark The part is poorly released or the ejector pressure is too high. White marks and bumps appear on the surface of the product: 3. Flow marks: The Part is not slippery, ...
- plastic injection part
- plastic part mould
- plastic molding
Splay Mark of Plastic Products Sep 17, 2019
Splay mark is a normal problem during manufacture plastic products. There are a few reason cause this problem: 1. The material contains water, drying time is insufficient. 2. Weld back pressure is too small or no back pressure. 3. Venting is not so good. We need keep to drying the material, Increasing back pressure, Improving the mould venting.
- Plastic mould
- Plastic injection mold
- mould venting
Actual Case Analysis of Poor Shrinkage (4) Sep 23, 2019
1. Basic information: PMMA Case, shrinkage 2. Description: Using a injection machine with a clamping force of 70 tons (screw diameter of 32 mm, maximum injection amount of 115 g: GP-PS), whether a molded part with a weight of 179.6 g and a thickness of 17 mm can be molded is tested. do. The main problems are as follows: (1) The amount of injection is not enough. In order to solve this problem, we ...
- PMMA case mould
- PMMA injection molding
- plastic molded part
The Manufacturing Processes for Plastic Products Sep 27, 2019
The manufacturing process of a plastic article refers to a process of making a final plastic article from a polymer manufactured by a synthetic resin manufacturer. Processing methods include: compression molding, extrusion molding, injection molding, blow molding etc. Detailed manufacturing process: (1) Compression Molding: Molding is also called press molding. It is mainly used for the mold...

1 ... 4 5 6 7 8 ... 12

A total of 12 pages

Categories

Blog

New Blog

Tags

Search