Custom Furniture Mould Manufacturing,Furniture Mould Manufacturing Manufacturers

Actual Case Analysis of Poor Shrinkage (2) Aug 09, 2019
Today we are continuing to discuss another case for the sink mark, we will show what we would do when we face the sink mark problem. 1. Basic information: ABS Case shrinkage 2. Description: a. Even if the maximum injection pressure is selected for molding, shrinkage will occur in the place where Rib is behind the molded part. b. As shown in picture, the cross-sectional area of the gate...
- plastic case mold
- ABS case mould
- plastic molded part
Injection molding and blow molding Sep 18, 2019
Plastic molding is a process in which a synthetic resin is used to make a final plastic product. Processing methods include: compression molding (molding), extrusion (extrusion), injection molding (injection molding), and blow molding (hollow molding). Let's distinguish between the molding process of injection molding and blow molding. (1) Injection molding: Injection molding is a method in which ...
- Blow Molding
- bottles molding
- Plastic Bucket Mould
What is venting defective of product? Aug 19, 2019
When the injection machine starts to molding，the hot melt plastic flows in the mold cavity and squeezes the air in the mold cavity. If the air cannot be discharged effectively, it will cause venting, and the result will be that the product is short-shot or affects the quality. Under this situation, We need to check the injection speed, the mold temperature, Or add venting groove.
- injection mold
- Plastic mould
- molding
Actual Case Analysis of Poor Shrinkage (3) Aug 23, 2019
Today we are continuing to discuss the 3rd case for the sink mark, we will show what we would do when we face the sink mark problem. 1. Basic information: PC combination transparent block, poor shrinkage 2. Description: there is not enough holding pressure time, but it is easy to cause flash by increasing the injection pressure. 3. Improvement: Increase the holding pressure time (with a pressure o...
- transparent part mold
- PC resin mould
- plastic molded part
What is the different between plastic mould and plastic injection mould? Sep 09, 2019
Plastic mould include injection mould, plastic injection mould is one of plastic mould. Plastic mould is a joint name of compression mould, extrusion mould, injection mould, blow mould and foaming mould. Plastic mould is a tool to manufacture plastic products, it could make plastic products to be more complete and the size more accurate.
- Plastic injection mold
- foaming mould
- extrusion mould
Plastic injection product defects discussion Sep 18, 2019
Today we are going to discuss common defects for plastic injection products. 1. Short shot The plastic part is insufficiently filled (or the injection pressure is not enough, the mold nozzle is too small). 2. Ejector Mark The part is poorly released or the ejector pressure is too high. White marks and bumps appear on the surface of the product: 3. Flow marks: The Part is not slippery, ...
- plastic injection part
- plastic part mould
- plastic molding
Know about Polycarbonate Sep 17, 2019
PC is an amorphous engineering material with exceptional impact strength, thermal stability, gloss, bacterial inhibition, flame retardant properties and stain resistance. The otched Izod impact stregth of the PC is very high, and the shrinkage rate is very low, generally 0.1 to 0.5%. PC has good mechanical properties, but its flow characteristics are poor, so the injection molding process of this ...
Splay Mark of Plastic Products Sep 17, 2019
Splay mark is a normal problem during manufacture plastic products. There are a few reason cause this problem: 1. The material contains water, drying time is insufficient. 2. Weld back pressure is too small or no back pressure. 3. Venting is not so good. We need keep to drying the material, Increasing back pressure, Improving the mould venting.
- Plastic mould
- Plastic injection mold
- mould venting

1 ... 4 5 6 7 8 ... 12

A total of 12 pages

Categories

Blog

New Blog

Tags

Search